@article {6930,
	title = {CUTTING TOOL LIFE AND ITS EFFECT ON SURFACE ROUGHNESS WHEN TURNING WITH WC-6\% CO},
	journal = {International Journal of Modern Manufacturing Technologies},
	volume = {XII},
	number = {2},
	year = {2020},
	abstract = {During turning operations, tool-part-chip contact causes wear to the cutting tool. The objective of this work is to study the wear of the clearance faces of tungsten carbide cutting tools during turning operations. Experimental tests on tool life for dry turning operations were carried out at four different cutting speeds, where the feed rate and the depth of cut are kept at constant values: 0.08 mm/rev for feed rate and 0.5 mm for depth of cut. An analysis of the influence of cutting parameters on the tools wear and consequently tool life (Τ) was presented, then the roughness of the machined surface Ra and the morphology of the chips produced were studied. This study makes it possible to identify that the wear mechanisms and the tool life are strongly linked to the roughness of the machined surfaces and to the morphology of the chips produced during the turning operations.},
	url = {https://modtech.ro/international-journal/vol12no22020/01_Mourad_Bendifallah.pdf},
	author = {Bendifallah, Mourad and Mourad Brioua and Belloufi, Abderrahim}
}
@article {63124,
	title = {Cutting Tool Life And Its Effect On Surface Roughness When Turning With WC-6\% CO},
	journal = {International Journal of Modern Manufacturing TechnologiesInternational Journal of Modern Manufacturing Technologies},
	volume = {12},
	year = {2020},
	month = {2020},
	pages = {7-16},
	author = {Bendifallah, Mourad and Mourad Brioua and Belloufi, Abderrahim}
}
@article {61649,
	title = {EXPERIMENTAL INVESTIGATION OF THE CORROSION RESISTANCE OF Ni-Al2O3 COMPOSITE COATINGS OBTAINED BY ELECTRODEPOSITION},
	journal = {U.P.B. Sci. Bull., Series B, },
	volume = {82},
	number = {1},
	year = {2020},
	abstract = {
	This article aims to prepare Ni-Al2O3 composite coatings from a conventional electroplating process. The coatings development parameters taken into account for this study of the corrosion resistance of these coatings are: Al2O3 concentration, bath temperature and current. The experimental tests are carried out by two lost mass and polarization techniques. The objective of the work is to determine the influence of elaboration parameters on the corrosion resistance of NiAl2O3 composite coatings. The study carried out in this article has show

},
	url = {https://www.scientificbulletin.upb.ro/rev_docs_arhiva/fulla9c_658903.pdf},
	author = {Rezgui, Imane and Belloufi, Abderrahim and Mihi, Abdelkader}
}
@article {64201,
	title = {Fuzzy Logic Approach for Predicting the Effect of Manufacturing Parameters of Ni-Al2O3 Composite Coatings by Electrodeposition},
	journal = {International Journal of Modern Manufacturing TechnologiesInternational Journal of Modern Manufacturing Technologies},
	volume = {9},
	year = {2017},
	month = {2017},
	pages = {65-72},
	author = {Rezgui, Imane and Mihi, Abdelkader and Belloufi, Abderrahim and Abdelkrim, Mourad and Brabie, Gheorghe}
}
@article {65675,
	title = {Experimental and Numerical Study of the Cutting Temperature during the Turning of the C45 Steel},
	journal = {Applied Mechanics and Materials},
	volume = {823},
	year = {2016},
	month = {2016},
	pages = {507-512},
	publisher = {Trans Tech Publ},
	abstract = {
	In machining operation, the quality of surface finish is an important requirement for many turned work pieces. cutting temperature is one of the most important parameters in determining the cutting performance and tool life. the objective for this work is to estimate the cutting temperature in 3D model on tool-chip interface and the interface temperature during turning process, using the digital simulation software COMSOL Multiphysics.The tool{\textendash}chip interface temperature results obtained from experimental results by using C45 medium carbon steel work piece with natural contact tools, without the application of cooling and lubricating agents and a K type thermocouple technique was used for estimating cutting temperatures in a turning operation.This procedure facilitates the determination of the temperature at tool-chip interface in dry turning process, which is still a challenge for existing experimental and numerical methods.

},
	isbn = {3-03835-566-6},
	url = {https://www.scientific.net/AMM.823.507},
	author = {Abdelkrim, Mourad and Mourad Brioua and Belloufi, Abderrahim and Gherfi, Abdelhafid}
}
@proceedings {65674,
	title = {Experimental and Numerical Study of the Cutting Temperature during the Turning of the C45 Steel},
	journal = {Applied Mechanics and MaterialsApplied Mechanics and Materials},
	volume = {823},
	year = {2016},
	month = {2016},
	pages = {507-512},
	publisher = {Trans Tech Publ},
	isbn = {3-03835-566-6},
	author = {Abdelkrim, Mourad and Mourad Brioua and Belloufi, Abderrahim and Gherfi, Abdelhafid}
}
