@article {83374,
	title = {Cascade sliding mode maximum power point tracking controller for photovoltaic systems},
	journal = {Electrical Engineering \& Electromechanics},
	volume = {1},
	year = {2023},
	abstract = {
	Introduction.\&nbsp;Constant increases in power consumption by both industrial and individual users may cause depletion of fossil fuels and environmental pollution, and hence there is a growing interest in clean and renewable energy resources. Photovoltaic power generation systems are playing an important role as a clean power electricity source in meeting future electricity demands.\&nbsp;



	Problem. All photovoltaic systems have two problems; the first one being the very low electric-power generation efficiency, especially under low-irradiation states; the second resides in the interdependence of the amount of the electric power generated by solar arrays and the ever changing weather conditions. Load mismatch can occur under these weather varying conditions such that maximum power is not extracted and delivered to the load. This issue constitutes the so-called maximum power point tracking problem.



	\&nbsp;Aim.\&nbsp;Many methods have been developed to determine the maximum power point under all conditions. There are various methods, in most of them based on the well-known principle of perturb and observe. In this method, the operating point oscillates at a certain amplitude, no matter whether the maximum power point is reached or not. That is, this oscillation remains even in the steady state after reaching the maximum power point, which leads to power loss. This is an essential drawback of the previous method. In this paper, a cascade sliding mode maximum power point tracking control for a photovoltaic system is proposed to overcome above mentioned problems.\&nbsp;



	Methodology.\&nbsp;The photovoltaic system is mainly composed of a solar array, DC/DC boost converter, cascade sliding mode controller, and an output load. Two sliding mode control design strategies are joined to construct the proposed controller. The primary sliding mode algorithm is designed for maximum power point searching, i.e., to track the output reference voltage of the solar array. This voltage is used to manipulate the setpoint of the secondary sliding mode controller, which is used via the DC-DC boost converter to achieve maximum power output.\&nbsp;



	Results.\&nbsp;This novel approach provides a good transient response, a low tracking error and a very fast reaction against the solar radiation and photovoltaic cell temperature variations. The simulation results demonstrate the effectiveness of the proposed approach in the presence of environmental disturbances.

},
	url = {http://eie.khpi.edu.ua/article/view/266115},
	author = {Hessad, M-A and Bouchama, Ziyad and Benaggoune, Sa{\"\i}d and Behih, K}
}
@article {83373,
	title = {Indirect adaptive fuzzy finite time synergetic control for power systems},
	journal = {Electrical Engineering \& Electromechanics},
	volume = {1},
	year = {2023},
	abstract = {
	Introduction.\&nbsp;Budget constraints in a world ravenous for electrical power have led utility companies to operate generating stations with full power and sometimes at the limit of stability. In such drastic conditions the occurrence of any contingency or disturbance may lead to a critical situation starting with poorly damped oscillations followed by loss of synchronism and power system instability. In the past decades, the utilization of supplementary excitation control signals for improving power system stability has received much attention. Power system stabilizers (PSS) are used to generate supplementary control signals for the excitation system in order to damp low-frequency oscillations caused by load disturbances or short-circuit faults. Problem.\&nbsp;Adaptive power system stabilizers have been proposed to adequately deal with a wide range of operating conditions, but they suffer from the major drawback of requiring parameter model identification, state observation and on-line feedback gain computation. Power systems are nonlinear systems, with configurations and parameters that fluctuate with time that which require a fully nonlinear model and an adaptive control scheme for a practical operating environment. A new nonlinear adaptive fuzzy approach based on synergetic control theory which has been developed for nonlinear power system stabilizers to overcome above mentioned problems.



	Aim.\&nbsp;Synergetic control theory has been successfully applied in the design of power system stabilizers is a most promising robust control technique relying on the same principle of invariance found in sliding mode control, but without its chattering drawback. In most of its applications, synergetic control law was designed based on an asymptotic stability analysis and the system trajectories evolve to a specified attractor reaching the equilibrium in an infinite time. In this paper an indirect finite time adaptive fuzzy synergetic power system stabilizer for damping local and inter-area modes of oscillations for power systems is presented.\&nbsp;



	Methodology.\&nbsp;The proposed controller design is based on an adaptive fuzzy control combining a synergetic control theory with a finite-time attractor and Lyapunov synthesis. Enhancing existing adaptive fuzzy synergetic power system stabilizer, where fuzzy systems are used to approximate unknown system dynamics and robust synergetic control for only providing asymptotic stability of the closed-loop system, the proposed technique procures finite time convergence property in the derivation of the continuous synergetic control law. Analytical proofs for finite time convergence are presented confirming that the proposed adaptive scheme can guarantee that system signals are bounded and finite time stability obtained.\&nbsp;



	Results.\&nbsp;The performance of the proposed stabilizer is evaluated for a single machine infinite bus system and for a multi machine power system under different type of disturbances. Simulation results are compared to those obtained with a conventional adaptive fuzzy synergetic controller.

},
	url = {http://eie.khpi.edu.ua/article/view/267200},
	author = {Khatir, Abdelfatah and Bouchama, Ziyad and Benaggoune, Sa{\"\i}d and Zerroug, Nadjat}
}
@article {63098,
	title = {Design and experimental validation of an intelligent controller for DC{\textendash}DC buck converters},
	journal = {Journal of the Franklin InstituteJournal of the Franklin Institute},
	volume = {357},
	year = {2020},
	month = {2020},
	pages = {10353-10366},
	isbn = {0016-0032},
	author = {Bouchama, Ziyad and Khatir, Abdelfatah and Benaggoune, Sa{\"\i}d and Harmas, Mohamed Naguib}
}
@article {64609,
	title = {DSP-based implementation of fast terminal synergetic control for a DC{\textendash}DC Buck converter},
	journal = {Journal of the Franklin InstituteJournal of the Franklin Institute},
	volume = {355},
	year = {2018},
	month = {2018},
	pages = {2329-2343},
	isbn = {0016-0032},
	author = {Zerroug, Nadjat and Harmas, Mohamed Naguib and Benaggoune, Sa{\"\i}d and Bouchama, Ziyad and Zehar, Khaled}
}
