Landslides, fault movements as well as shrink/swell soil displacements can exert important additional loadings on soil buried structures such as pipelines. These loadings may damage the buried structures whenever they reach the strength limits of the structure material. This paper presents a two-dimensional plane-strain finite element analysis of an 800 mm diameter water supply pipeline buried within the expansive clay of the Ain-Tine area (Mila, Algeria), considering the unsaturated behavior of the soil under a rainfall infiltration of 4 mm/day intensity and which lasts for different time durations (8, 15 and 30 days). The simulations were carried out using the commercial software module SIGMA/W and considering different initial soil suction conditions P1, P2, P3 and P4. The soil surface heave and the radial induced forces on the pipeline ring (i.e., Axial , Shear  forces and bending moments ) results indicated that following the changes of suction the rainfall infiltration can cause considerable additional loads on the buried pipeline. Moreover, these loads are proportionally related to the initial soil suction conditions as well as to the rainfall infiltration time duration. The study highlighted that the unsaturated behavior of expansive soils because of their volume instability are very sensitive to climatic conditions and can exert adverse effects on pipelines buried within such soils. As a result, consistent pipeline design should seriously consider the study of the effect of the climatic conditions on the overall stability of the pipeline structure.

Landslides, fault movements as well as shrink/swell soil displacements can exert important additional loadings on soil buried structures such as pipelines. These loadings may damage the buried structures whenever they reach the strength limits of the structure material. This paper presents a two-dimensional plane-strain finite element analysis of an 800 mm diameter water supply pipeline buried within the expansive clay of the Ain-Tine area (Mila, Algeria), considering the unsaturated behavior of the soil under a rainfall infiltration of 4 mm/day intensity and which lasts for different time durations (8, 15 and 30 days). The simulations were carried out using the commercial software module SIGMA/W and considering different initial soil suction conditions P1, P2, P3 and P4. The soil surface heave and the radial induced forces on the pipeline ring (i.e., Axial , Shear  forces and bending moments ) results indicated that following the changes of suction the rainfall infiltration can cause considerable additional loads on the buried pipeline. Moreover, these loads are proportionally related to the initial soil suction conditions as well as to the rainfall infiltration time duration. The study highlighted that the unsaturated behavior of expansive soils because of their volume instability are very sensitive to climatic conditions and can exert adverse effects on pipelines buried within such soils. As a result, consistent pipeline design should seriously consider the study of the effect of the climatic conditions on the overall stability of the pipeline structure.

Landslides, fault movements as well as shrink/swell soil displacements can exert important additional loadings on soil buried structures such as pipelines. These loadings may damage the buried structures whenever they reach the strength limits of the structure material. This paper presents a two-dimensional plane-strain finite element analysis of an 800 mm diameter water supply pipeline buried within the expansive clay of the Ain-Tine area (Mila, Algeria), considering the unsaturated behavior of the soil under a rainfall infiltration of 4 mm/day intensity and which lasts for different time durations (8, 15 and 30 days). The simulations were carried out using the commercial software module SIGMA/W and considering different initial soil suction conditions P1, P2, P3 and P4. The soil surface heave and the radial induced forces on the pipeline ring (i.e., Axial , Shear  forces and bending moments ) results indicated that following the changes of suction the rainfall infiltration can cause considerable additional loads on the buried pipeline. Moreover, these loads are proportionally related to the initial soil suction conditions as well as to the rainfall infiltration time duration. The study highlighted that the unsaturated behavior of expansive soils because of their volume instability are very sensitive to climatic conditions and can exert adverse effects on pipelines buried within such soils. As a result, consistent pipeline design should seriously consider the study of the effect of the climatic conditions on the overall stability of the pipeline structure.

This article presents the results of experimental work carried out both in situ (coring; pressuremeter test) and in the laboratory (drying-wetting and oedometric tests) to describe the volumetric behavior on drying-wetting path of a swelling clayey soil of eastern Algeria. In order to perform drying-wetting tests the osmotic technique and saturated salts solutions were used. These suction-imposed methods have gained widespread acceptance as reliable methods for imposing suction on soil specimens. They allowed to sweep a wide range of suctions between 0 and 500 MPa. The ability to impose suction on soil specimens allows for drying and wetting stress paths to be applied to evaluate resulting changes in state parameters (void ratio, degree of saturation and water content). These paths were carried out on specimens with different initial states. Slurries of soil were used to characterize the reference behavior, while the undisturbed soil samples allow to describe the behavior of material under in situ conditions. In the last part of this article and to specify the behavior observed in the saturated domain, a comparison between the resulting deformations of the drying-wetting test and those resulting from the oedometric test was made.

This article presents the results of experimental work carried out both in situ (coring; pressuremeter test) and in the laboratory (drying-wetting and oedometric tests) to describe the volumetric behavior on drying-wetting path of a swelling clayey soil of eastern Algeria. In order to perform drying-wetting tests the osmotic technique and saturated salts solutions were used. These suction-imposed methods have gained widespread acceptance as reliable methods for imposing suction on soil specimens. They allowed to sweep a wide range of suctions between 0 and 500 MPa. The ability to impose suction on soil specimens allows for drying and wetting stress paths to be applied to evaluate resulting changes in state parameters (void ratio, degree of saturation and water content). These paths were carried out on specimens with different initial states. Slurries of soil were used to characterize the reference behavior, while the undisturbed soil samples allow to describe the behavior of material under in situ conditions. In the last part of this article and to specify the behavior observed in the saturated domain, a comparison between the resulting deformations of the drying-wetting test and those resulting from the oedometric test was made.

This article presents the results of experimental work carried out both in situ (coring; pressuremeter test) and in the laboratory (drying-wetting and oedometric tests) to describe the volumetric behavior on drying-wetting path of a swelling clayey soil of eastern Algeria. In order to perform drying-wetting tests the osmotic technique and saturated salts solutions were used. These suction-imposed methods have gained widespread acceptance as reliable methods for imposing suction on soil specimens. They allowed to sweep a wide range of suctions between 0 and 500 MPa. The ability to impose suction on soil specimens allows for drying and wetting stress paths to be applied to evaluate resulting changes in state parameters (void ratio, degree of saturation and water content). These paths were carried out on specimens with different initial states. Slurries of soil were used to characterize the reference behavior, while the undisturbed soil samples allow to describe the behavior of material under in situ conditions. In the last part of this article and to specify the behavior observed in the saturated domain, a comparison between the resulting deformations of the drying-wetting test and those resulting from the oedometric test was made.

This article presents the results of experimental work carried out both in situ (coring; pressuremeter test) and in the laboratory (drying-wetting and oedometric tests) to describe the volumetric behavior on drying-wetting path of a swelling clayey soil of eastern Algeria. In order to perform drying-wetting tests the osmotic technique and saturated salts solutions were used. These suction-imposed methods have gained widespread acceptance as reliable methods for imposing suction on soil specimens. They allowed to sweep a wide range of suctions between 0 and 500 MPa. The ability to impose suction on soil specimens allows for drying and wetting stress paths to be applied to evaluate resulting changes in state parameters (void ratio, degree of saturation and water content). These paths were carried out on specimens with different initial states. Slurries of soil were used to characterize the reference behavior, while the undisturbed soil samples allow to describe the behavior of material under in situ conditions. In the last part of this article and to specify the behavior observed in the saturated domain, a comparison between the resulting deformations of the drying-wetting test and those resulting from the oedometric test was made.

This article presents the results of experimental work carried out both in situ (coring; pressuremeter test) and in the laboratory (drying-wetting and oedometric tests) to describe the volumetric behavior on drying-wetting path of a swelling clayey soil of eastern Algeria. In order to perform drying-wetting tests the osmotic technique and saturated salts solutions were used. These suction-imposed methods have gained widespread acceptance as reliable methods for imposing suction on soil specimens. They allowed to sweep a wide range of suctions between 0 and 500 MPa. The ability to impose suction on soil specimens allows for drying and wetting stress paths to be applied to evaluate resulting changes in state parameters (void ratio, degree of saturation and water content). These paths were carried out on specimens with different initial states. Slurries of soil were used to characterize the reference behavior, while the undisturbed soil samples allow to describe the behavior of material under in situ conditions. In the last part of this article and to specify the behavior observed in the saturated domain, a comparison between the resulting deformations of the drying-wetting test and those resulting from the oedometric test was made.

This article presents the results of experimental work carried out both in situ (coring; pressuremeter test) and in the laboratory (drying-wetting and oedometric tests) to describe the volumetric behavior on drying-wetting path of a swelling clayey soil of eastern Algeria. In order to perform drying-wetting tests the osmotic technique and saturated salts solutions were used. These suction-imposed methods have gained widespread acceptance as reliable methods for imposing suction on soil specimens. They allowed to sweep a wide range of suctions between 0 and 500 MPa. The ability to impose suction on soil specimens allows for drying and wetting stress paths to be applied to evaluate resulting changes in state parameters (void ratio, degree of saturation and water content). These paths were carried out on specimens with different initial states. Slurries of soil were used to characterize the reference behavior, while the undisturbed soil samples allow to describe the behavior of material under in situ conditions. In the last part of this article and to specify the behavior observed in the saturated domain, a comparison between the resulting deformations of the drying-wetting test and those resulting from the oedometric test was made.

This papers deal with a new Adaptive Direct Power Control for Doubly-Fed Induction Generator of 1.5 MW. The main feature of the proposed strategy is based on the replacement of the fixed switching table by an adaptive one. The online update of the adaptive switching table depends on the reactive power variation and past switching sequences. The proposed adaptive direct power control is compared with Vector Control and Classical Direct Power Control. The robustness of the proposed control scheme against parameter, load and wind speed variations have done with success. The main performance of the Adaptive Direct Power Control strategy is the reduction of powers ripples, thus reduce of torque ripple on the shaft of the turbine.

This papers deal with a new Adaptive Direct Power Control for Doubly-Fed Induction Generator of 1.5 MW. The main feature of the proposed strategy is based on the replacement of the fixed switching table by an adaptive one. The online update of the adaptive switching table depends on the reactive power variation and past switching sequences. The proposed adaptive direct power control is compared with Vector Control and Classical Direct Power Control. The robustness of the proposed control scheme against parameter, load and wind speed variations have done with success. The main performance of the Adaptive Direct Power Control strategy is the reduction of powers ripples, thus reduce of torque ripple on the shaft of the turbine.

This papers deal with a new Adaptive Direct Power Control for Doubly-Fed Induction Generator of 1.5 MW. The main feature of the proposed strategy is based on the replacement of the fixed switching table by an adaptive one. The online update of the adaptive switching table depends on the reactive power variation and past switching sequences. The proposed adaptive direct power control is compared with Vector Control and Classical Direct Power Control. The robustness of the proposed control scheme against parameter, load and wind speed variations have done with success. The main performance of the Adaptive Direct Power Control strategy is the reduction of powers ripples, thus reduce of torque ripple on the shaft of the turbine.

This papers deal with a new Adaptive Direct Power Control for Doubly-Fed Induction Generator of 1.5 MW. The main feature of the proposed strategy is based on the replacement of the fixed switching table by an adaptive one. The online update of the adaptive switching table depends on the reactive power variation and past switching sequences. The proposed adaptive direct power control is compared with Vector Control and Classical Direct Power Control. The robustness of the proposed control scheme against parameter, load and wind speed variations have done with success. The main performance of the Adaptive Direct Power Control strategy is the reduction of powers ripples, thus reduce of torque ripple on the shaft of the turbine.

This papers deal with a new Adaptive Direct Power Control for Doubly-Fed Induction Generator of 1.5 MW. The main feature of the proposed strategy is based on the replacement of the fixed switching table by an adaptive one. The online update of the adaptive switching table depends on the reactive power variation and past switching sequences. The proposed adaptive direct power control is compared with Vector Control and Classical Direct Power Control. The robustness of the proposed control scheme against parameter, load and wind speed variations have done with success. The main performance of the Adaptive Direct Power Control strategy is the reduction of powers ripples, thus reduce of torque ripple on the shaft of the turbine.

Cette thèse traite la modélisation, le contrôle et la simulation d’un système de conversion d’énergie éolienne à base d’une machine synchrone à aimants permanents (GSAP) connectée au réseau. Il est nécessaire de lier cette génératrice avec la charge ou le réseau par des convertisseurs statiques susceptibles d’améliorer la qualité d’énergie en tension et fréquence en utilisant des techniques adéquates de commande. L’étude consiste à implémenter des stratégies de contrôle pour assurer une meilleure qualité d’énergie. Après la modélisation de la cha{\^ıne de conversion d’énergie éolienne complète avec exploitation de la commande MPPT, une application de la commande directe du couple basée sur des régulateurs à hystérésis et la commande DTC-SVM sont introduites à la machine pour mettre en évidences les performances de ces dernières. D’après les résultats de simulation obtenus, la commande DTC-SVM présente de meilleures performances par rapport à la DTC classique et la commande vectorielle

Cette thèse a pour but d’apporter une contribution au contrôle DTC de la MASDE. Plusieurs structures ont été développées ces structures concernant la combinaison de différentes techniques de commandes intelligentes avec l’apport des techniques d’optimisations. Dans ce contexte une commande floue type 1 et flou type 2 ont été présentée avec l’utilisation des techniques PSO et AG dont le but est d’améliorer les performances de la MASDE, avec ces techniques les oscillations de flux et couple sont réduites, et la réponse dynamique du système a été améliorée. Dans ce travail, nous avons aussi développé une autre technique qui réduit les oscillations de couple et de flux, cette technique que nous avons appelée commande DTC hybride basée sur le mode glissant d’ordre supérieur flou-T2. L’ensemble des résultats obtenus a montré satisfaction quant aux performances atteintes par le système. Celles-ci sont traduites par la robustesse de la commande vis-à-vis des incertitudes paramétriques de la MASDE.

Ce travail est basé sur l’étude et la simulation numérique du comportement de la micropompe piézoélectrique à mouvement péristaltique. La nature de l’actionneur piézoélectrique est un disque piézoélectrique PZT-5H (Titano-Zirconate de Plomb) et le diaphragme est un dioxyde de silicium (SiO2). En appliquant l’approche FSI (Fluid-Structure Interaction), la simulation de la micropompe sans valves est réalisée au moyen du logiciel Comsol 3.5 Multiphysics. La déformation dûe à la tension appliquée aux bornes du disque piézoélectrique entra{\^ıne un déplacement de la membrane, et par la meme la circulation du fluide. A partir des résultats obtenus, la conception optimale a nécessité respectivement une épaisseur de 0.5 mm pour la membrane et pour l’actionneur piézoéléctrique. L’étude des effets de la tension sur la déflexion du diaphragme et la nature du fluide sur le débit de la micropompe a été menée et des résultats de simulation probants ont été obtenus

Ce travail présente des techniques de commande robustes dédiées au système éolien basé sur la machine asynchrone à double alimentation sans balais (MADASB) entrainée par une turbine à calage variable des pales. Le stator de puissance de la machine est directement relié au réseau électrique ; par contre le stator de commande est alimenté par un convertisseur bidirectionnel. Les MADASB promettent des avantages significatifs pour les systèmes de conversion d’énergie éolienne en raison de leurs faibles coûts et une plus grande fiabilité par rapport aux machines asynchrones à double alimentation classiques (MADA). L’idée principale consiste à appliquer différentes techniques de commande pour le contrôle indépendant des puissances active et réactive générées par la MADASB découplée par la technique de commande vectorielle. Il s’agit particulièrement de la commande par logique floue et des commandes par mode glissant d’ordre un et de second ordre basée sur l’algorithme du Super-Twisting, la commande par retour d’état et la commande par backstepping. Une étude comparative relative aux performances obtenues par les commandes proposées est menée. Les résultats de simulation montrent que ces méthodes hiérarchisées, possèdent de grandes performances dans le contrôle de tels systèmes en termes de poursuite de la référence, de découplage, de temps de réponse et de la qualité du courant.