In this article, we present a comparative study between two control techniques applied on the Permanent Magnet Synchronous Machine (PMSM), namely vector control and fuzzy logic. This comparison is based on three criteria: qualitative, quantitative and robust during the transient and permanent operation of the system. The latter comprises a machine is driven through the stator variables by two bidirectional converters. In the first part, we have presented the individual modeling of the global chain (PMSM, Inverter, and Rectifier). Then we presented and developed the two commands techniques to control the speed and the torque produced by this machine. The results of this study made it possible to evaluate the performance of these controls.

In this article, we present a comparative study between two control techniques applied on the Permanent Magnet Synchronous Machine (PMSM), namely vector control and fuzzy logic. This comparison is based on three criteria: qualitative, quantitative and robust during the transient and permanent operation of the system. The latter comprises a machine is driven through the stator variables by two bidirectional converters. In the first part, we have presented the individual modeling of the global chain (PMSM, Inverter, and Rectifier). Then we presented and developed the two commands techniques to control the speed and the torque produced by this machine. The results of this study made it possible to evaluate the performance of these controls.

In this article, we present a comparative study between two control techniques applied on the Permanent Magnet Synchronous Machine (PMSM), namely vector control and fuzzy logic. This comparison is based on three criteria: qualitative, quantitative and robust during the transient and permanent operation of the system. The latter comprises a machine is driven through the stator variables by two bidirectional converters. In the first part, we have presented the individual modeling of the global chain (PMSM, Inverter, and Rectifier). Then we presented and developed the two commands techniques to control the speed and the torque produced by this machine. The results of this study made it possible to evaluate the performance of these controls.

This paper presents a comparative study between two strategies for the direct torque control (DTC) of the permanent magnet synchronous generator (PMSG) based on wind energy conversion system (WECS). The first method is a conventional direct torque control DTC and it is based on hysteresis controllers where the torque and the flux are regulated by these controllers. The second one is direct torque control by space vector modulation strategy (DTC-SVM) where the torque and flux are regulated by PI controllers. The simulation results are implemented by using MATLAB/SIMULINK. The main feature of the proposed (DTC-SVM) strategy is the reduction of torque and flux ripples. The proposed approach can be considered as an alternative solution to the control of PMSG.

This paper presents a comparative study between two strategies for the direct torque control (DTC) of the permanent magnet synchronous generator (PMSG) based on wind energy conversion system (WECS). The first method is a conventional direct torque control DTC and it is based on hysteresis controllers where the torque and the flux are regulated by these controllers. The second one is direct torque control by space vector modulation strategy (DTC-SVM) where the torque and flux are regulated by PI controllers. The simulation results are implemented by using MATLAB/SIMULINK. The main feature of the proposed (DTC-SVM) strategy is the reduction of torque and flux ripples. The proposed approach can be considered as an alternative solution to the control of PMSG.

This paper presents a comparative study between two strategies for the direct torque control (DTC) of the permanent magnet synchronous generator (PMSG) based on wind energy conversion system (WECS). The first method is a conventional direct torque control DTC and it is based on hysteresis controllers where the torque and the flux are regulated by these controllers. The second one is direct torque control by space vector modulation strategy (DTC-SVM) where the torque and flux are regulated by PI controllers. The simulation results are implemented by using MATLAB/SIMULINK. The main feature of the proposed (DTC-SVM) strategy is the reduction of torque and flux ripples. The proposed approach can be considered as an alternative solution to the control of PMSG.

This paper presents a comparative study between two strategies for the direct torque control (DTC) of the permanent magnet synchronous generator (PMSG) based on wind energy conversion system (WECS). The first method is a conventional direct torque control DTC and it is based on hysteresis controllers where the torque and the flux are regulated by these controllers. The second one is direct torque control by space vector modulation strategy (DTC-SVM) where the torque and flux are regulated by PI controllers. The simulation results are implemented by using MATLAB/SIMULINK. The main feature of the proposed (DTC-SVM) strategy is the reduction of torque and flux ripples. The proposed approach can be considered as an alternative solution to the control of PMSG.

This paper presents a comparative study between two strategies for the direct torque control (DTC) of the permanent magnet synchronous generator (PMSG) based on wind energy conversion system (WECS). The first method is a conventional direct torque control DTC and it is based on hysteresis controllers where the torque and the flux are regulated by these controllers. The second one is direct torque control by space vector modulation strategy (DTC-SVM) where the torque and flux are regulated by PI controllers. The simulation results are implemented by using MATLAB/SIMULINK. The main feature of the proposed (DTC-SVM) strategy is the reduction of torque and flux ripples. The proposed approach can be considered as an alternative solution to the control of PMSG.

This paper presents a comparative study between two strategies for the direct torque control (DTC) of the permanent magnet synchronous generator (PMSG) based on wind energy conversion system (WECS). The first method is a conventional direct torque control DTC and it is based on hysteresis controllers where the torque and the flux are regulated by these controllers. The second one is direct torque control by space vector modulation strategy (DTC-SVM) where the torque and flux are regulated by PI controllers. The simulation results are implemented by using MATLAB/SIMULINK. The main feature of the proposed (DTC-SVM) strategy is the reduction of torque and flux ripples. The proposed approach can be considered as an alternative solution to the control of PMSG.

This investigation examines mathematical modelling and experimental validation of two types of solar cookers: a box type with tilted intercept area equipped with one external reflector, and a parabolic cooker with a new configuration. Experiments were carried out with the cookers filled with two kilograms of water from 08:00 to 15:00 solar time. During the experiments, temperature gain in the box-type solar cooker was recorded at about 69.8 °C and in the parabolic-type solar cooker at 73.6 °C at the stagnation point. Direct normal irradiation in three distinct study areas was observed and found that it varied from 7.6 to 10 kWh m⁻². Cooking pot placed in parabolic cooker was varied between 130 and 132 °C. Centre and south-east regions of study areas where global irradiation varied from 8 to 8.4 kWh m⁻² were found suitable for box-type solar cooker and cooking pot temperature were found in the range of 100 °C to 105 °C. Mathematical modelling was programmed in MATLAB. The theoretical results were consistent with experiential data for both types of solar cookers. The effectiveness of the two cooker types can be deduced from the maps. It is found the use of the cookers in Northern and Southern regions of the country was not identical. Their suitability for cooking depends on the amount of solar radiations received.

This investigation examines mathematical modelling and experimental validation of two types of solar cookers: a box type with tilted intercept area equipped with one external reflector, and a parabolic cooker with a new configuration. Experiments were carried out with the cookers filled with two kilograms of water from 08:00 to 15:00 solar time. During the experiments, temperature gain in the box-type solar cooker was recorded at about 69.8 °C and in the parabolic-type solar cooker at 73.6 °C at the stagnation point. Direct normal irradiation in three distinct study areas was observed and found that it varied from 7.6 to 10 kWh m⁻². Cooking pot placed in parabolic cooker was varied between 130 and 132 °C. Centre and south-east regions of study areas where global irradiation varied from 8 to 8.4 kWh m⁻² were found suitable for box-type solar cooker and cooking pot temperature were found in the range of 100 °C to 105 °C. Mathematical modelling was programmed in MATLAB. The theoretical results were consistent with experiential data for both types of solar cookers. The effectiveness of the two cooker types can be deduced from the maps. It is found the use of the cookers in Northern and Southern regions of the country was not identical. Their suitability for cooking depends on the amount of solar radiations received.

This investigation examines mathematical modelling and experimental validation of two types of solar cookers: a box type with tilted intercept area equipped with one external reflector, and a parabolic cooker with a new configuration. Experiments were carried out with the cookers filled with two kilograms of water from 08:00 to 15:00 solar time. During the experiments, temperature gain in the box-type solar cooker was recorded at about 69.8 °C and in the parabolic-type solar cooker at 73.6 °C at the stagnation point. Direct normal irradiation in three distinct study areas was observed and found that it varied from 7.6 to 10 kWh m⁻². Cooking pot placed in parabolic cooker was varied between 130 and 132 °C. Centre and south-east regions of study areas where global irradiation varied from 8 to 8.4 kWh m⁻² were found suitable for box-type solar cooker and cooking pot temperature were found in the range of 100 °C to 105 °C. Mathematical modelling was programmed in MATLAB. The theoretical results were consistent with experiential data for both types of solar cookers. The effectiveness of the two cooker types can be deduced from the maps. It is found the use of the cookers in Northern and Southern regions of the country was not identical. Their suitability for cooking depends on the amount of solar radiations received.

This investigation examines mathematical modelling and experimental validation of two types of solar cookers: a box type with tilted intercept area equipped with one external reflector, and a parabolic cooker with a new configuration. Experiments were carried out with the cookers filled with two kilograms of water from 08:00 to 15:00 solar time. During the experiments, temperature gain in the box-type solar cooker was recorded at about 69.8 °C and in the parabolic-type solar cooker at 73.6 °C at the stagnation point. Direct normal irradiation in three distinct study areas was observed and found that it varied from 7.6 to 10 kWh m⁻². Cooking pot placed in parabolic cooker was varied between 130 and 132 °C. Centre and south-east regions of study areas where global irradiation varied from 8 to 8.4 kWh m⁻² were found suitable for box-type solar cooker and cooking pot temperature were found in the range of 100 °C to 105 °C. Mathematical modelling was programmed in MATLAB. The theoretical results were consistent with experiential data for both types of solar cookers. The effectiveness of the two cooker types can be deduced from the maps. It is found the use of the cookers in Northern and Southern regions of the country was not identical. Their suitability for cooking depends on the amount of solar radiations received.

This investigation examines mathematical modelling and experimental validation of two types of solar cookers: a box type with tilted intercept area equipped with one external reflector, and a parabolic cooker with a new configuration. Experiments were carried out with the cookers filled with two kilograms of water from 08:00 to 15:00 solar time. During the experiments, temperature gain in the box-type solar cooker was recorded at about 69.8 °C and in the parabolic-type solar cooker at 73.6 °C at the stagnation point. Direct normal irradiation in three distinct study areas was observed and found that it varied from 7.6 to 10 kWh m⁻². Cooking pot placed in parabolic cooker was varied between 130 and 132 °C. Centre and south-east regions of study areas where global irradiation varied from 8 to 8.4 kWh m⁻² were found suitable for box-type solar cooker and cooking pot temperature were found in the range of 100 °C to 105 °C. Mathematical modelling was programmed in MATLAB. The theoretical results were consistent with experiential data for both types of solar cookers. The effectiveness of the two cooker types can be deduced from the maps. It is found the use of the cookers in Northern and Southern regions of the country was not identical. Their suitability for cooking depends on the amount of solar radiations received.

The magnetohydrodynamics (MHD) is an important interdisciplinary field. It is the interaction between an electromagnetic field and an electrically conducting fluid. Electromagnetic pumps are widely used for the transportation of the fluids in a variety of technological processes. The advantage of these devices is that permits the pumping of liquids without moving parts. The design of the pump is considered as an optimization problem where the objective function is the minimum of the MHD pump mass with both geometrical and electromagnetic contraints type. The obtained optimization results using the finite volume method with Matlab software show the performances of the used stochastic simulated annealing method.

The magnetohydrodynamics (MHD) is an important interdisciplinary field. It is the interaction between an electromagnetic field and an electrically conducting fluid. Electromagnetic pumps are widely used for the transportation of the fluids in a variety of technological processes. The advantage of these devices is that permits the pumping of liquids without moving parts. The design of the pump is considered as an optimization problem where the objective function is the minimum of the MHD pump mass with both geometrical and electromagnetic contraints type. The obtained optimization results using the finite volume method with Matlab software show the performances of the used stochastic simulated annealing method.

The magnetohydrodynamics (MHD) is an important interdisciplinary field. It is the interaction between an electromagnetic field and an electrically conducting fluid. Electromagnetic pumps are widely used for the transportation of the fluids in a variety of technological processes. The advantage of these devices is that permits the pumping of liquids without moving parts. The design of the pump is considered as an optimization problem where the objective function is the minimum of the MHD pump mass with both geometrical and electromagnetic contraints type. The obtained optimization results using the finite volume method with Matlab software show the performances of the used stochastic simulated annealing method.