The resonant characteristics of superconducting rectangular microstrip patch antenna witha superstrate layer are investigated using a full-wave spectral analysis in conjunction with the complexresistive boundary condition. The complex surface impedance of superconducting patch is determinedusing London’s equation and the two-fluid model of Gorter and Casimir. Numerical results using thefull-wave analysis presented here are in excellent agreement with theoretical and experimental resultsavailable in the open literature. Numerical results show that the effect of the superstrate layer on theresonant frequency and half-power bandwidth of the superconducting rectangular patch is stronger thanthat of the structure without superstrate layer as both the thickness and permittivity of the superstrateincrease. Finally, numerical results concerning the effects of the parameters of superstrate-substrateand superconducting patch on the antenna performance are also presented and discussed

The effect of the presence of electron–phonon (e–ph) coupling in the SiC, GeC and SnC hybrids is studied in the framework of the ab initio perturbation theory. The electronic bang gap thermal dependence reveals a normal monotonic decrease in the SiC and GeC semiconductors, whereas SnC exhibits an anomalous behavior. The electron line widths were evaluated and the contributions of acoustic and optical phonon modes to the imaginary part of the self-energy were determined. It has been found that the e–ph scattering rates are globally controlled by the out-of-plane acoustic transverse mode ZA in SiC while both ZA and ZO are overriding in GeC. In SnC, the out-of-plane transverse optical mode ZO is the most dominant. The relaxation lifetime of the photo-excited electrons shows that the thermalization of the hot carrier occurs at 90 fs, 100 fs and 120 fs in SiC, GeC and SnC, respectively. The present study properly describes the subpicosecond time scale after sunlight illumination using an approach that requires no empirical data. The results make the investigated structures suitable for providing low cost and high-performance optical communication and monitoring applications using 2D materials.

In this paper, a new Se/CZTSSe tandem solar cell architecture is proposed as a viable approach to reach ultrahigh efficiency values at low fabrication cost. The proposed tandem design consists of a Se-based top cell with Ti intermediate ultra-thin metallic layers (MLs) and a CZTS bottom cell with graded band-gap aspect. The role of the introduced design amendments in achieving the dual-benefit of enhanced optical behavior and reduced recombination losses is investigated by means of an accurate numerical modeling. Moreover, a comprehensive study which involves the impact of design parameters such as the MLs position and the CZTSSe band-gap profile on the device performance is carried out. Moreover, Particle Swarm Optimization (PSO)-based metaheuristic technique is used to boost up the Se/CZTSSe tandem cell efficiency by identifying both the suitable position of the introduced ultrathin MLs and the appropriate CZTSSe band-gap profile. It is found that the adopted optimization approach pinpoints a new path toward achieving over 30% efficiency, not only it provides the possibility to reduce interface recombination effects by optimizing the band offset at the buffer/absorber interfaces but also enables selecting the most favorable design configuration associated with enhanced optical behavior. This makes the optimized Se/CZTSSe tandem solar cell potential alternative for providing high-efficiency and stable tandem solar cell.

This investigation examines mathematical modelling and experimental validation of two types of solar cookers: a box type with tilted intercept area equipped with one external reflector, and a parabolic cooker with a new configuration. Experiments were carried out with the cookers filled with two kilograms of water from 08:00 to 15:00 solar time. During the experiments, temperature gain in the box-type solar cooker was recorded at about 69.8 °C and in the parabolic-type solar cooker at 73.6 °C at the stagnation point. Direct normal irradiation in three distinct study areas was observed and found that it varied from 7.6 to 10 kWh m^-$². Cooking pot placed in parabolic cooker was varied between 130 and 132 °C. Centre and south-east regions of study areas where global irradiation varied from 8 to 8.4 kWh m^-$² were found suitable for box-type solar cooker and cooking pot temperature were found in the range of 100 °C to 105 °C. Mathematical modelling was programmed in MATLAB. The theoretical results were consistent with experiential data for both types of solar cookers. The effectiveness of the two cooker types can be deduced from the maps. It is found the use of the cookers in Northern and Southern regions of the country was not identical. Their suitability for cooking depends on the amount of solar radiations received.

The smart grid system is key to the new electrical network infrastructure. It takes into account the use of the new information and communication technologies (ITC) and the integration of the renewable energy power generation (photovoltaics PV, concentrated solar power CSP, wind, etc). The smart grid promises better management and control of energy sources. The application of the smart grid, especially, in Algeria allows the optimal control of the electricity demand since the latter keeps rising continuously. The use of smart grid allows the rationalization of the electricity consumption in smart homes through appliance automated control. Input energy savings result in the reduction of c emission. Herein, we present a new energy management strategy tested in an experimental smart home (SM). The implemented management approach was made possible by using a new electronic system that allowed the control of all appliances via the internet network. For this purpose, a dynamic monitoring web interface was developed under an open source platform in order to process the whole data delivered by the system. The final output of the system which consists of a balance between all types of energy involved, including CO2 gas emission, is displayed. It is only then that the user can take adequate decision and establish the priorities for rational use of the energy available.