Sedimentation of dam reservoirs is a complex problem with several dimensions, including filling rates and characteristics of accumulated sediments. Sediment supply from river basins is particularly high in this region because of its semi-arid climate and especially because of poor vegetation protection. The amount of silt accumulated annually since the construction of this dam is estimated at 330000 m3. This silt accumulation strongly limits its storage capacity and consequently its operating duration. The consequences of this serious problem have been catastrophic, including a considerable reduction of 43–84% of the storage capacity of the dams and a clear degradation of water quality that can cause the degradation of the ecosystem functioning and can lead to irreversible changes. The silt present in abundance in the Algerian dams can, thus, constitute a potential resource to be judiciously exploited towards the increase of the performances of the construction materials. The extraction of sediments accumulated in the dam reservoir is, therefore, imperative. These sediments have a great geotechnical value. The objective of this study is to assess the feasibility of the recovery of mud by studying the knowledge of the sediments of the dam of Koudiat Medouar. The results of the tests carried out in laboratory allowed us to identify the various sediments from a physical and geotechnical point of view. These materials must of course meet certain rigorous criteria in terms of mechanical strength and durability and environmental impact. The experimental approach that we adopted allowed us to determine the characteristics of the materials necessary for the realization of compressed earth bricks (BTC) in conformity with the recommendations of the technical guides of construction.

Sedimentation of dam reservoirs is a complex problem with several dimensions, including filling rates and characteristics of accumulated sediments. Sediment supply from river basins is particularly high in this region because of its semi-arid climate and especially because of poor vegetation protection. The amount of silt accumulated annually since the construction of this dam is estimated at 330000 m3. This silt accumulation strongly limits its storage capacity and consequently its operating duration. The consequences of this serious problem have been catastrophic, including a considerable reduction of 43–84% of the storage capacity of the dams and a clear degradation of water quality that can cause the degradation of the ecosystem functioning and can lead to irreversible changes. The silt present in abundance in the Algerian dams can, thus, constitute a potential resource to be judiciously exploited towards the increase of the performances of the construction materials. The extraction of sediments accumulated in the dam reservoir is, therefore, imperative. These sediments have a great geotechnical value. The objective of this study is to assess the feasibility of the recovery of mud by studying the knowledge of the sediments of the dam of Koudiat Medouar. The results of the tests carried out in laboratory allowed us to identify the various sediments from a physical and geotechnical point of view. These materials must of course meet certain rigorous criteria in terms of mechanical strength and durability and environmental impact. The experimental approach that we adopted allowed us to determine the characteristics of the materials necessary for the realization of compressed earth bricks (BTC) in conformity with the recommendations of the technical guides of construction.

In the industry, automated inspection is important for ensuring the high quality and allows acceleration of procedures for quality control of parts or mechanical assemblies. Although significant progress has been made in precision machining of complex surfaces, precision inspection of such surfaces remains a difficult problem. Thus the problem of the conformity of the parts of complex geometry is felt more and more. Motivated by the need to increase quality and reduce costs, and supported by the progress made in the field of it as well as the automation of production which in recent years has seen a considerable evolution in all these stages: from design to control through manufacturing. Due to, we used a 3D computer aided inspection technique on a physical gear using a coordinate measuring machine equipped with a “PC-DMIS” measurement and inspection software. Our work consists in developing a procedure for inspection for reproduction of gear profile by reconstruction of a circle involute gear from a cloud point’s measurement. In order to obtain a reliable result. In this works, we design the CAD-model of the part as accurately as possible (using a mathematical model) and matched with the 3D points cloud that represents the measurement that obtained from scanner. we compare the measurement cloud points from coordinate measurement machine with the mathematical model of construction by ICP (Iterative Closest Point) methods in order to obtain a conformed result and to show the impact of the dimensional inspection and geometric.

In the industry, automated inspection is important for ensuring the high quality and allows acceleration of procedures for quality control of parts or mechanical assemblies. Although significant progress has been made in precision machining of complex surfaces, precision inspection of such surfaces remains a difficult problem. Thus the problem of the conformity of the parts of complex geometry is felt more and more. Motivated by the need to increase quality and reduce costs, and supported by the progress made in the field of it as well as the automation of production which in recent years has seen a considerable evolution in all these stages: from design to control through manufacturing. Due to, we used a 3D computer aided inspection technique on a physical gear using a coordinate measuring machine equipped with a “PC-DMIS” measurement and inspection software. Our work consists in developing a procedure for inspection for reproduction of gear profile by reconstruction of a circle involute gear from a cloud point’s measurement. In order to obtain a reliable result. In this works, we design the CAD-model of the part as accurately as possible (using a mathematical model) and matched with the 3D points cloud that represents the measurement that obtained from scanner. we compare the measurement cloud points from coordinate measurement machine with the mathematical model of construction by ICP (Iterative Closest Point) methods in order to obtain a conformed result and to show the impact of the dimensional inspection and geometric.

In the industry, automated inspection is important for ensuring the high quality and allows acceleration of procedures for quality control of parts or mechanical assemblies. Although significant progress has been made in precision machining of complex surfaces, precision inspection of such surfaces remains a difficult problem. Thus the problem of the conformity of the parts of complex geometry is felt more and more. Motivated by the need to increase quality and reduce costs, and supported by the progress made in the field of it as well as the automation of production which in recent years has seen a considerable evolution in all these stages: from design to control through manufacturing. Due to, we used a 3D computer aided inspection technique on a physical gear using a coordinate measuring machine equipped with a “PC-DMIS” measurement and inspection software. Our work consists in developing a procedure for inspection for reproduction of gear profile by reconstruction of a circle involute gear from a cloud point’s measurement. In order to obtain a reliable result. In this works, we design the CAD-model of the part as accurately as possible (using a mathematical model) and matched with the 3D points cloud that represents the measurement that obtained from scanner. we compare the measurement cloud points from coordinate measurement machine with the mathematical model of construction by ICP (Iterative Closest Point) methods in order to obtain a conformed result and to show the impact of the dimensional inspection and geometric.

Designing and manufacturing replacement cancellous bone structures by lattice structures and Additive Manufacturing (AM) techniques is an effective method to create lightweight orthopedic implants while ensuring that they are mechanically compatible and their osseointegration ability with the host bone. In this article, we suggest a new design based on three lattice structures from triply periodic minimal surfaces (TPMS) with a different volume porosity to replace cancellous bone based on predicting the mechanical stiffness. To predict the mechanical stiffness, the relationship between the effective modulus of elasticity and different porosity ratios of the lattice structures was determined by using three methods: i) finite element modeling (FEM) simulation, ii) Gibson and Ashby method and iii) a uniaxial compression test after manufacturing the lattice structures by using Fused Filament Fabrication (FFF) Technology. To demonstrate the efficiency of our approach, the comparison of both numerical and experimental results showed that the effect of structure difference and porosity ratio of lattice structures on the mechanical stiffness values effectively match the cancellous bone in terms of elastic modulus and porosity ratio.

Designing and manufacturing replacement cancellous bone structures by lattice structures and Additive Manufacturing (AM) techniques is an effective method to create lightweight orthopedic implants while ensuring that they are mechanically compatible and their osseointegration ability with the host bone. In this article, we suggest a new design based on three lattice structures from triply periodic minimal surfaces (TPMS) with a different volume porosity to replace cancellous bone based on predicting the mechanical stiffness. To predict the mechanical stiffness, the relationship between the effective modulus of elasticity and different porosity ratios of the lattice structures was determined by using three methods: i) finite element modeling (FEM) simulation, ii) Gibson and Ashby method and iii) a uniaxial compression test after manufacturing the lattice structures by using Fused Filament Fabrication (FFF) Technology. To demonstrate the efficiency of our approach, the comparison of both numerical and experimental results showed that the effect of structure difference and porosity ratio of lattice structures on the mechanical stiffness values effectively match the cancellous bone in terms of elastic modulus and porosity ratio.

Designing and manufacturing replacement cancellous bone structures by lattice structures and Additive Manufacturing (AM) techniques is an effective method to create lightweight orthopedic implants while ensuring that they are mechanically compatible and their osseointegration ability with the host bone. In this article, we suggest a new design based on three lattice structures from triply periodic minimal surfaces (TPMS) with a different volume porosity to replace cancellous bone based on predicting the mechanical stiffness. To predict the mechanical stiffness, the relationship between the effective modulus of elasticity and different porosity ratios of the lattice structures was determined by using three methods: i) finite element modeling (FEM) simulation, ii) Gibson and Ashby method and iii) a uniaxial compression test after manufacturing the lattice structures by using Fused Filament Fabrication (FFF) Technology. To demonstrate the efficiency of our approach, the comparison of both numerical and experimental results showed that the effect of structure difference and porosity ratio of lattice structures on the mechanical stiffness values effectively match the cancellous bone in terms of elastic modulus and porosity ratio.

Designing and manufacturing replacement cancellous bone structures by lattice structures and Additive Manufacturing (AM) techniques is an effective method to create lightweight orthopedic implants while ensuring that they are mechanically compatible and their osseointegration ability with the host bone. In this article, we suggest a new design based on three lattice structures from triply periodic minimal surfaces (TPMS) with a different volume porosity to replace cancellous bone based on predicting the mechanical stiffness. To predict the mechanical stiffness, the relationship between the effective modulus of elasticity and different porosity ratios of the lattice structures was determined by using three methods: i) finite element modeling (FEM) simulation, ii) Gibson and Ashby method and iii) a uniaxial compression test after manufacturing the lattice structures by using Fused Filament Fabrication (FFF) Technology. To demonstrate the efficiency of our approach, the comparison of both numerical and experimental results showed that the effect of structure difference and porosity ratio of lattice structures on the mechanical stiffness values effectively match the cancellous bone in terms of elastic modulus and porosity ratio.

Designing and manufacturing replacement cancellous bone structures by lattice structures and Additive Manufacturing (AM) techniques is an effective method to create lightweight orthopedic implants while ensuring that they are mechanically compatible and their osseointegration ability with the host bone. In this article, we suggest a new design based on three lattice structures from triply periodic minimal surfaces (TPMS) with a different volume porosity to replace cancellous bone based on predicting the mechanical stiffness. To predict the mechanical stiffness, the relationship between the effective modulus of elasticity and different porosity ratios of the lattice structures was determined by using three methods: i) finite element modeling (FEM) simulation, ii) Gibson and Ashby method and iii) a uniaxial compression test after manufacturing the lattice structures by using Fused Filament Fabrication (FFF) Technology. To demonstrate the efficiency of our approach, the comparison of both numerical and experimental results showed that the effect of structure difference and porosity ratio of lattice structures on the mechanical stiffness values effectively match the cancellous bone in terms of elastic modulus and porosity ratio.

The relative scarcity of water resources in Algeria and their unequal distribution induce a rational use of available resources. The Zana-Gada{\"ıne plain appears as an exemplary case study, where the difficulties posed by the problem of crop water needs versus the availability of water resources appear. This article, based on field surveys and in-situ measurements, aims to identify the pressure of irrigation on water resources and the optimization of their use in an agricultural area, where irrigated agriculture represents 85% of the water consumption of the Zana-Gada{\"ıne plain. The piezometric study in correlation with hydrogeological data reveals that groundwater resources are limited, aggravated by wastage resulting in a consequent drawdown of 24 meters over 11 years. The analysis of interannual climate variability has enabled us to draw rainfall maps characteristic of the evolution of rainfall over the past decades where we observe a net deficit in precipitation. We calculated the evapotranspiration and the requirements in irrigation water for each crop in order to compare them with the available hydric resources and the establishment of irrigation schedules for the principal irrigated crops. The analysis of interannual climate variability has enabled us to draw rainfall maps characteristic of the evolution of rainfall over the past decades where we observe a net deficit in precipitation. We calculated the evapotranspiration and the requirements in irrigation water for each crop in order to compare them with the available hydric resources and the establishment of irrigation schedules for the principal irrigated crops.

The relative scarcity of water resources in Algeria and their unequal distribution induce a rational use of available resources. The Zana-Gada{\"ıne plain appears as an exemplary case study, where the difficulties posed by the problem of crop water needs versus the availability of water resources appear. This article, based on field surveys and in-situ measurements, aims to identify the pressure of irrigation on water resources and the optimization of their use in an agricultural area, where irrigated agriculture represents 85% of the water consumption of the Zana-Gada{\"ıne plain. The piezometric study in correlation with hydrogeological data reveals that groundwater resources are limited, aggravated by wastage resulting in a consequent drawdown of 24 meters over 11 years. The analysis of interannual climate variability has enabled us to draw rainfall maps characteristic of the evolution of rainfall over the past decades where we observe a net deficit in precipitation. We calculated the evapotranspiration and the requirements in irrigation water for each crop in order to compare them with the available hydric resources and the establishment of irrigation schedules for the principal irrigated crops. The analysis of interannual climate variability has enabled us to draw rainfall maps characteristic of the evolution of rainfall over the past decades where we observe a net deficit in precipitation. We calculated the evapotranspiration and the requirements in irrigation water for each crop in order to compare them with the available hydric resources and the establishment of irrigation schedules for the principal irrigated crops.

The relative scarcity of water resources in Algeria and their unequal distribution induce a rational use of available resources. The Zana-Gada{\"ıne plain appears as an exemplary case study, where the difficulties posed by the problem of crop water needs versus the availability of water resources appear. This article, based on field surveys and in-situ measurements, aims to identify the pressure of irrigation on water resources and the optimization of their use in an agricultural area, where irrigated agriculture represents 85% of the water consumption of the Zana-Gada{\"ıne plain. The piezometric study in correlation with hydrogeological data reveals that groundwater resources are limited, aggravated by wastage resulting in a consequent drawdown of 24 meters over 11 years. The analysis of interannual climate variability has enabled us to draw rainfall maps characteristic of the evolution of rainfall over the past decades where we observe a net deficit in precipitation. We calculated the evapotranspiration and the requirements in irrigation water for each crop in order to compare them with the available hydric resources and the establishment of irrigation schedules for the principal irrigated crops. The analysis of interannual climate variability has enabled us to draw rainfall maps characteristic of the evolution of rainfall over the past decades where we observe a net deficit in precipitation. We calculated the evapotranspiration and the requirements in irrigation water for each crop in order to compare them with the available hydric resources and the establishment of irrigation schedules for the principal irrigated crops.

The security is so important for both storing and transmitting the digital data, the choice of parameters is critical for a security system, that is, a weak parameter will make the scheme very vulnerable to attacks, for example the use of supersingular curves or anomalous curves leads to weaknesses in elliptic curve cryptosystems, for RSA cryptosystem there are some attacks for low public exponent or small private exponent. In certain circumstances the secret sharing scheme is required to decentralize the risk. In the context of the security of secret sharing schemes, it is known that for the scheme of Shamir, an unqualified set of shares cannot leak any information about the secret. This paper aims to show that the well-known Shamir’s secret sharing is not always perfect and that the uniform randomization before sharing is insufficient to obtain a secure scheme. The second purpose of this paper is to give an explicit construction of weak polynomials for which the Shamir’s (k, n) threshold scheme is insecure in the sense that there exist a fewer than k shares which can reconstruct the secret. Particular attention is given to the scheme whose threshold is less than or equal to 6. It also showed that for certain threshold k, the secret can be calculated by a pair of shares with the probability of 1/2. Finally, in order to address the mentioned vulnerabilities, several classes of polynomials should be avoided.

Graph matching is a comparison process of two objects represented as graphs through finding a correspondence between vertices and edges. This process allows defining a similarity degree (or dissimilarity) between the graphs. Generally, graph matching is used for extracting, finding and retrieving any information or sub-information that can be represented by graphs. In this paper, a new consistency rule is proposed to tackle with various problems of graph matching. After, using the proposed rule as a necessary and sufficient condition for the graph isomorphism, we generalize it for subgraph isomorphism, homomorphism and for an example of inexact graph matching. To determine whether there is a matching or not, a backtracking algorithm called CRGI2 is presented who checks the consistency rule by exploring the overall search space. The tree-search is consolidated with a tree pruning technique that eliminates the unfruitful branches as early as possible. Experimental results show that our algorithm is efficient and applicable for a real case application in the information retrieval field. On the efficiency side, due to the ability of the proposed rule to eliminate as early as possible the incorrect solutions, our algorithm outperforms the existing algorithms in the literature. For the application side, the algorithm has been successfully tested for querying a real dataset that contains a large set of e-mail messages.

Graph matching is a comparison process of two objects represented as graphs through finding a correspondence between vertices and edges. This process allows defining a similarity degree (or dissimilarity) between the graphs. Generally, graph matching is used for extracting, finding and retrieving any information or sub-information that can be represented by graphs. In this paper, a new consistency rule is proposed to tackle with various problems of graph matching. After, using the proposed rule as a necessary and sufficient condition for the graph isomorphism, we generalize it for subgraph isomorphism, homomorphism and for an example of inexact graph matching. To determine whether there is a matching or not, a backtracking algorithm called CRGI2 is presented who checks the consistency rule by exploring the overall search space. The tree-search is consolidated with a tree pruning technique that eliminates the unfruitful branches as early as possible. Experimental results show that our algorithm is efficient and applicable for a real case application in the information retrieval field. On the efficiency side, due to the ability of the proposed rule to eliminate as early as possible the incorrect solutions, our algorithm outperforms the existing algorithms in the literature. For the application side, the algorithm has been successfully tested for querying a real dataset that contains a large set of e-mail messages.

This paper introduces a new approach of hybrid meta-heuristics based optimization technique for decreasing the computation time of the shortest paths algorithm. The problem of finding the shortest paths is a combinatorial optimization problem which has been well studied from various fields. The number of vehicles on the road has increased incredibly. Therefore, traffic management has become a major problem. We study the traffic network in large scale routing problems as a field of application. The meta-heuristic we propose introduces new hybrid genetic algorithm named IOGA. The problem consists of finding the k optimal paths that minimizes a metric such as distance, time, etc. Testing was performed using an exact algorithm and meta-heuristic algorithm on random generated network instances. Experimental analyses demonstrate the efficiency of our proposed approach in terms of runtime and quality of the result. Empirical results obtained show that the proposed algorithm outperforms some of the existing technique in term of the optimal solution in every generation.

This paper introduces a new approach of hybrid meta-heuristics based optimization technique for decreasing the computation time of the shortest paths algorithm. The problem of finding the shortest paths is a combinatorial optimization problem which has been well studied from various fields. The number of vehicles on the road has increased incredibly. Therefore, traffic management has become a major problem. We study the traffic network in large scale routing problems as a field of application. The meta-heuristic we propose introduces new hybrid genetic algorithm named IOGA. The problem consists of finding the k optimal paths that minimizes a metric such as distance, time, etc. Testing was performed using an exact algorithm and meta-heuristic algorithm on random generated network instances. Experimental analyses demonstrate the efficiency of our proposed approach in terms of runtime and quality of the result. Empirical results obtained show that the proposed algorithm outperforms some of the existing technique in term of the optimal solution in every generation.