In the present work, Fe-Cu based alloys with different compositions have been obtained by using Powder metallurgy (PM). These alloys were created with the purpose of increasing mechanical properties of the parts. Nevertheless, little have been published, once this is a matter of industrial interest. In this work, samples of Fe100-x Cux (x=0.40, 0.55, 0.70, 0.85 and 1) alloys were processed by cold pressing at 10 MPa, followed by sintering at 1250 C°. Structures formed during sintering were studied by EDS. Microstructural aspects were observed by MEB. Densification and microhardness tests were also performed.

Baseline wander (BW) is a common low frequency artifact in electrocardiogram (ECG) signals. The prime cause from which BW arises is the patient’s breathing and movement. To facilitate reliable visual interpretation of the ECG and to discern particular patterns in the ECG signal, BW needs to be removed. In this paper, a novel BW removal method is presented. The hypothesis is based on the observation that ECG signal variation covaries with its BW. As such, the P, Q, R, S, and T peaks will follow the baseline drift. On this basis, the following proposition is true: a reliable approximation of the baseline drift can be obtained from the shape derived from the interpolation of one form of the ECG signal peak (peak envelope). The simulation was performed by adding artificial BW to ECG signal recordings. The signal-to-noise ratio, mean squared error, and improvement factor criteria were used to numerically evaluate the performance of the proposed approach. The technique was compared to that of the Hilbert vibration decomposition method, an empirical-mode decomposition technique and mathematical morphology. The results of the simulation indicate that the proposed technique is most effective in situations where there is a considerable distortion in the baseline wandering.

This paper was made in the region of M’daourouch-Dréa which is part of the high plains of northeastern Algeria, located southwest of the Souk-ahras Wilaya in eastern Algeria. It is a plain with agricultural vocation which requires for its development more water. Knowing that the rainfall is low (465mm/year) and not enough to meet the needs of farmers, the use of groundwater then becomes the only alternative to fill this lack of resources. Among the aquifers identified in this region is that contained in fissured limestones of lower Maestrichian age. In order to satisfy farmers and citizens in water it is necessary to have a good characterization of this aquifer. The objective of this paper is to improve the knowledge on the morphology and the extension of this aquifer and to locate its roof in space to help operators choose areas favorable to exploitation, so direct them to the nearest areas of the surface thus minimizing the cost of the drilling operation. To achieve this goal, we have exploited by exploiting several tools (geological map, logs of boreholes and geophysics survey), whose combination gave an idea on the geometry of the aquifer as well as the depth of its roof in different regions of the plain and shows by the occasion, the affectation of these limestones by several tectonic accidents generating thus a structure in collapsed blocks from where the very variable depth of the roof of these limestones of a place of the plain to other.

This paper was made in the region of M’daourouch-Dréa which is part of the high plains of northeastern Algeria, located southwest of the Souk-ahras Wilaya in eastern Algeria. It is a plain with agricultural vocation which requires for its development more water. Knowing that the rainfall is low (465mm/year) and not enough to meet the needs of farmers, the use of groundwater then becomes the only alternative to fill this lack of resources. Among the aquifers identified in this region is that contained in fissured limestones of lower Maestrichian age. In order to satisfy farmers and citizens in water it is necessary to have a good characterization of this aquifer. The objective of this paper is to improve the knowledge on the morphology and the extension of this aquifer and to locate its roof in space to help operators choose areas favorable to exploitation, so direct them to the nearest areas of the surface thus minimizing the cost of the drilling operation. To achieve this goal, we have exploited by exploiting several tools (geological map, logs of boreholes and geophysics survey), whose combination gave an idea on the geometry of the aquifer as well as the depth of its roof in different regions of the plain and shows by the occasion, the affectation of these limestones by several tectonic accidents generating thus a structure in collapsed blocks from where the very variable depth of the roof of these limestones of a place of the plain to other.